Someone can help me with a PHRT16 - Iam from Germany

[OskarInDerTonne]

Hi ACH31,
this ECH PDF File is what I´m looking for. Thx. Of course the Parameter A11 is not the right one. I think its the A20 - but I don´t can change it. Your real time synoptic is great. thx for your help - maybee someone knows the way to stop the waterpump if the machine is on standby.


Greetings
Ibo

[yoannd]

Bonsoir ACH31:
Toutes mes félicitations: réponse en anglais, et en plus, en stéréo
Au fait, je risque de passer chez toi demain soir si tu es là. Mais, ce n'est pas tout à fait sûr, car je ne sais pas à quelle heure je vais terminer demain soir à Monsérié.
A + Georges32

Georges, this post is in english... Chaleurterre is the best world forum for the PAC, isn't it ?

[MAMO]

Georges have a 56K modem

The life is too hard in gers

Good evening ! Nicolas...

[ACH31]

I have reduced the temperature of activating pump last winter, and also the hysterisis (A12). You can do it with A11 .
You can see on the other doc i give you the url, at page 51 it says :

A20 : Special antifreeze: water pump on set point
Value of AI1 below which water pump is enabled.

A20 is not accesible, but with the A11 in fact you can choise the temperature of activation of the pump (in fact the min value is -12° A11=-10 (-A20) = -12°)

But if you do that, you have to set A13 at maximum !

[OskarInDerTonne]

I have reduced the temperature of activating pump last winter, and also the hysterisis (A12). You can do it with A11 .
You can see on the other doc i give you the url, at page 51 it says :

A20 : Special antifreeze: water pump on set point
Value of AI1 below which water pump is enabled.

A20 is not accesible, but with the A11 in fact you can choise the temperature of activation of the pump (in fact the min value is -12° A11=-10 (-A20) = -12°)

Ok I have set the A11 to - 10°

But if you do that, you have to set A13 at maximum !

and also I have set the A13 to 255 who is maximum. But what meaning has the parameter A13

Thx

greetings
Ibo

[ACH31]

If A13 reach the limit, it will stop the pump, with alarm code E05

[OskarInDerTonne]

ok I understand thx . I will see. When It works it is a milestone in my PHRT Configuration. All other is ok. Wich Programm do you use for your real time synoptic ?

bye Ibo

[Georges32]

Yes, yes, I am sorry, good-by
George thirty two

[ACH31]

For the synoptic, I use a lot of software !
The main is Homeseer wich have also a web server, I use it , I create a web page with Asp.
The monitoring of temperatures is done with a 1wire Lan and Logtemp software.
I have also a meteostation (OREGON) and use Graphweather sofware. All these datas are colected by Homeseer.
The webpage is "animed" on my server, but for the public, I use url2bmp witch transform a web page in a picture file, and I transfer it by ftp every 5 mn to my FAI (done by Homeseer).
I give you by mp the direct url to my server to see it.
An other people do quite the same you can see : http://solaire.open-dream.org/

Bye

[OskarInDerTonne]

I have reduced the temperature of activating pump last winter, and also the hysterisis (A12). You can do it with A11 .
You can see on the other doc i give you the url, at page 51 it says :

A20 : Special antifreeze: water pump on set point
Value of AI1 below which water pump is enabled.

A20 is not accesible, but with the A11 in fact you can choise the temperature of activation of the pump (in fact the min value is -12° A11=-10 (-A20) = -12°)

Ok I have set the A11 to - 10°

But if you do that, you have to set A13 at maximum !

and also I have set the A13 to 255 who is maximum.
Thx

greetings
Ibo

Hello Again,
it don´t work so. No It´s here -1,0 ° and the Watterpump is working (PHRT on Standby). The parameter are set as you said but the Waterpump still works .
What else can I do ?

bye
ibo